#1
|
||||
|
||||
XLR Adapters
Been thinking about trying a set of XLR adapters. These would be for my TT so RCA's on that end and XLR at the Luxman integrated, which would allow me to use a "balanced" input. Any real advantage here or just a waste of $$?
__________________
[SIGPIC][/SIGPIC]2-Channel System: Luxman L590Aii, D-05 CD/SACD ,VPI Classic 3 (Rolling Stone photo shoot table), VPI SDS, Shelter 501 MKII , Wilson Audio Duette,Shunyata Denali 6000T, Anaconda Zitron, Alpha Digital, and Black Mamba power cables, Tara Labs RSC Air 2 speaker wire, RSC Prime M1 IC's. |
#2
|
||||
|
||||
Quote:
Best Sir, Bob
__________________
Amps:VAC 450iQ Monos in Silver Flake on HRS M3X2-1921's, HRS G7 Footers/G-Links & Sound Anchor Conecoasters. Preamp:VAC Statement (on order) (Silver Flake) Digital Source: dCS Rossini CD/SACD Transport, Vivaldi APEX DAC, Upsampler Plus & matching Clock (Silver) Analogue Preamp:VAC Renaissance SE Phono stage in Silver Flake with XLR Output Option & with Nordost Valhalla XLR's. Analogue Sources:SME 20/2 w/SME V arm & Nordost Odin 2 Tone Arm Cable, Palo Santos Presentation Cartridge & Akai GX-400D Reel-to-Reel w/relapped heads by JRF Magnetic Sciences. Akai RC-17 cabled remote (original owner since 1974). Vibration Control:TT on HRS M3X2-1921 shelf. Speakers:Wilson Audio Alexia V (on order in Ferrari Argento Silver/Parchment grills sitting on Acoustic Diode Kit). Power Cables:4 Nordost Odin Supreme Reference on amps, preamp & DAC. Ansuz Acoustics C2 on Transport & Clock. Power Distribution:Ansuz Mainz D3 Distributor & Ansuz Mainz C2 1M Power Cable Power Outlets:Furutech GTX-D NCF (R) duplex outlet, GTX Wall Plate & Duplex Cover (x2) on dedicated, same panel phase, 20A breakers. Speaker Cables:2M Nordost Odin 2 Supreme Reference on Nordost Sort Lifts. Signal Cables:Nordost Odin XLR's on dCS DAC & Amps. Digital Cables: Nordost Odin 2's, 110-ohm AES/EBU on dCS Transport to DAC. Clock Cables:5 each 75 ohm 1.25M Nordost Valhalla BNC/BNC Digital Ethernet Cable: WireWorld Platinum 1M Starlight® 8 Twinax Headphones:Vintage Koss Pro IV AA. RCM: Audio Desk PRO Tube Test Gear:Mint late '60's/calibrated Heathkit TT-1A, MaxiMatcher Power Amp & Preamp & Space Tech Labs ATT-3.02 tube test sets. |
#3
|
||||
|
||||
Your Luxman has phono stage input that uses XLR connections?
|
#4
|
||||
|
||||
never mind
__________________
[SIGPIC][/SIGPIC]2-Channel System: Luxman L590Aii, D-05 CD/SACD ,VPI Classic 3 (Rolling Stone photo shoot table), VPI SDS, Shelter 501 MKII , Wilson Audio Duette,Shunyata Denali 6000T, Anaconda Zitron, Alpha Digital, and Black Mamba power cables, Tara Labs RSC Air 2 speaker wire, RSC Prime M1 IC's. |
#5
|
|||
|
|||
More secure connection.
|
#6
|
||||
|
||||
I did exactly that for a while. My phono preamp was not balanced but I wanted to use balanced cables into my preamp. I used a pair of Canare XLR to RCA converters and it worked just fine. The reason I did this was because I knew I was going to upgrade my phono preamp in the near future. A pair of converters was much cheaper than a pair of interconnects.
|
#7
|
||||
|
||||
XLR Adapters
Unless your preamp or integrated amp has an XLR input specifically for “PHONO” input, you’ll be feeding the turntable’s low level output to a Line Level input, thereby bypassing the internal RIAA EQ filter. This will adversely affect the sound of vinyl. No?
Also, the turntable is outputting a very small signal, which the internal phono stage amplifies. I would think there will be a large mismatch in volume if using the line input rather than the phono input. Last edited by Cohibaman; 01-12-2018 at 05:59 PM. |
#8
|
|||
|
|||
D'Agostino supplies some pretty nice single ended to XLR adaptors with his Momentum amps. I ended up using them on the connection from my E-03 to met pre-amp. If I want to go all balanced I would have to move up to the e-04.
Last edited by Still-One; 01-12-2018 at 07:04 PM. |
#9
|
||||
|
||||
Quote:
At least that's how I interpreted the OP. Phono stages I have seen, if they offer XLR connectors, they also offer SE. In the OP's case, what would be gained by adding an XLR connector to the equipment SE side -- nothing. Thus my response. BTW, you must mean the E-02. Best Sir, Bob
__________________
Amps:VAC 450iQ Monos in Silver Flake on HRS M3X2-1921's, HRS G7 Footers/G-Links & Sound Anchor Conecoasters. Preamp:VAC Statement (on order) (Silver Flake) Digital Source: dCS Rossini CD/SACD Transport, Vivaldi APEX DAC, Upsampler Plus & matching Clock (Silver) Analogue Preamp:VAC Renaissance SE Phono stage in Silver Flake with XLR Output Option & with Nordost Valhalla XLR's. Analogue Sources:SME 20/2 w/SME V arm & Nordost Odin 2 Tone Arm Cable, Palo Santos Presentation Cartridge & Akai GX-400D Reel-to-Reel w/relapped heads by JRF Magnetic Sciences. Akai RC-17 cabled remote (original owner since 1974). Vibration Control:TT on HRS M3X2-1921 shelf. Speakers:Wilson Audio Alexia V (on order in Ferrari Argento Silver/Parchment grills sitting on Acoustic Diode Kit). Power Cables:4 Nordost Odin Supreme Reference on amps, preamp & DAC. Ansuz Acoustics C2 on Transport & Clock. Power Distribution:Ansuz Mainz D3 Distributor & Ansuz Mainz C2 1M Power Cable Power Outlets:Furutech GTX-D NCF (R) duplex outlet, GTX Wall Plate & Duplex Cover (x2) on dedicated, same panel phase, 20A breakers. Speaker Cables:2M Nordost Odin 2 Supreme Reference on Nordost Sort Lifts. Signal Cables:Nordost Odin XLR's on dCS DAC & Amps. Digital Cables: Nordost Odin 2's, 110-ohm AES/EBU on dCS Transport to DAC. Clock Cables:5 each 75 ohm 1.25M Nordost Valhalla BNC/BNC Digital Ethernet Cable: WireWorld Platinum 1M Starlight® 8 Twinax Headphones:Vintage Koss Pro IV AA. RCM: Audio Desk PRO Tube Test Gear:Mint late '60's/calibrated Heathkit TT-1A, MaxiMatcher Power Amp & Preamp & Space Tech Labs ATT-3.02 tube test sets. Last edited by vintage_tube; 01-12-2018 at 07:01 PM. |
#10
|
|||
|
|||
Quote:
|
|
|
Audio Aficionado Sponsors | |