#1
|
|||
|
|||
ET5 question ...
Was there an update for the ET5 to remain at the last source selected or does it always revert back to the CD input? Mine reverts back to the CD input. Not a big deal, but I thought I read somewhere they fixed that. Was anything else done along with that update. Of course, I'll call Ed on Monday. Just wondering if anyone else is familiar with it.
Thanks! |
#2
|
||||
|
||||
My CT-5 does exactly the same thing. I had heard there was a "firmware" fix for this, but I don't know if it's true...
__________________
Lumin P1 streamer/DAC/preamp, Constellation Inspiration integrated TT: Michell Gyro SE MkII, SME V, Koetsu Urushi Vermilion, EAR324. Harbeth 30.2s, REL R-305, Shunyata Alpha V2 ICs, Alpha V2 SPs, Sigma XC, Sigma NRv2, Omega QR-s & Alpha NRv2 PCs, segmented Altaira SG stack w/ Alpha & Omega CGCs, Everest 8000 PD. Remote Server Room: Uptone EtherREGEN, AfterDark Master Clock & LPS, Alita, Battle Angel, (Akasa NUC Roon Core), iFi DC Purifiers (for SMPS used for Alita & router), Shunyata Gemini combo power distributor & Altaira-type CG GP-NR hub, Venom & Alpha CGCs, Shunyata NRv14 power cords for digital components. |
#3
|
||||
|
||||
Joe, it's the same thing with the GAT....
__________________
Philippe l LP12SE,urika phonostage,radikal power supply, dynavector XV-1s,conrad-johnson GAT and LP275M, Sonus Faber Elipsa,yter/naim/Linn cables, vibex, finite elemente |
#4
|
||||
|
||||
Really, WTF
Does it also go back to vol 20 or stay at the last volume? The prem 16 and ART go back to the last source when you switch back on and last volume setting. Unless you pull the power plug out, it then goes to CD, vol 20. |
#5
|
|||
|
|||
I'll check it again. But I think it goes back to the last volume set and cd input on power up. Not 20 on volume. I'll report when I am positive.
|
#6
|
||||
|
||||
GAT stays on the last volume setting
__________________
Philippe l LP12SE,urika phonostage,radikal power supply, dynavector XV-1s,conrad-johnson GAT and LP275M, Sonus Faber Elipsa,yter/naim/Linn cables, vibex, finite elemente |
#7
|
|||
|
|||
Quote:
if AC is removed, then both input AND level go to default: 20-20 and CD input. OBTW, yes, in both cases whether "old" or "new" firmware, volume level is remembered. Also, just for those rare occasions when you remove the AC power to the units. Once AC has been restored, upon the initial power up, the mute circuit seems to not work and IF you happen to have power amps on when you turn the ETX on, you'll get a nasty noise. beyond first power up after AC connected the muting works fine, so even if you happen to forget the sequence of power up/power down, no problem. Last edited by Rayooo; 09-17-2011 at 06:55 PM. |
#8
|
||||
|
||||
That is good to see.
Worse is Audio Research. I had the new LS27 at home for a month. Every time you switched it off, then back on the volume would start at ZERO. PITA |
#9
|
|||
|
|||
Quote:
A friend of mine years ago as we moved into replacing potentiometers and mechanical switches with "digital" control...always said: "the best way to remember a potentiometer setting or a switch position is by using a potentiometer or a switch, not a set of logic ICs." but of course the advantage of digital control outweigh the few minor issues. Last edited by Rayooo; 09-17-2011 at 07:15 PM. |
#10
|
|||
|
|||
Joeinid,
Did you look into that new firmware for your ET-5? |
|
|
Audio Aficionado Sponsors | |