#1
|
||||
|
||||
Speaker cable questions.
1. I Bi-amp my B&W 802 and currently use two seperate cables. Should I get one run of WW Eclipse then bi -wire . Or two runs of the WW Equinox 6.
2. I have the Marantz MM8003 Amp the binding posts on the back have these plastic wrap around sheilds. I don't wan't to go bare wire and I don't think eithe the bannanas or spades will work any ideas
__________________
Marantz( UD8004,AV8802a ), Oppo udp 203 JLAudio Fathom F-110, B&W( 802 series III , FCMS8, SCMS8) . WireWorld Eclipse 6 xlr(7) Sliver Eclipse 5.2 HDMI (3) electra 5.2 powercords . HRS Nimbus , lg 55 Oled Nvidia Shield PS Audio PPP System 2 Panasonic G25 Marantz av8003 Last edited by Doug Lax; 12-30-2010 at 12:52 PM. |
#2
|
||||
|
||||
I would go bi-wire or just pick up a set of nice jumpers.
Why wouldn't nanners work? http://us.marantz.com/MM8003_REAR_PA...1200_96dpi.jpg
__________________
2CH: W4S DAC-2, W4S STP-SE, W4S SX-500, Custom ScanSpeak/SEAS Towers, Hot Rodded Rega TT and Jolida JD9 Phono Pre, Asynch PC Transport, WireWorld Gold Eclipse 6 XLR HT: Marantz AV7005, W4S Mini MC-5, Custom Waveguide Towers, SVSPB12-Plus/2 |
#3
|
||||
|
||||
They may work. I am a little concerned about them staying put and having enough contact area as the black plastic tabs allow you to put it in but the screw in the center prevents it from going all the way through
__________________
Marantz( UD8004,AV8802a ), Oppo udp 203 JLAudio Fathom F-110, B&W( 802 series III , FCMS8, SCMS8) . WireWorld Eclipse 6 xlr(7) Sliver Eclipse 5.2 HDMI (3) electra 5.2 powercords . HRS Nimbus , lg 55 Oled Nvidia Shield PS Audio PPP System 2 Panasonic G25 Marantz av8003 Last edited by Doug Lax; 12-30-2010 at 12:55 PM. |
#4
|
||||
|
||||
WW banana plugs are epically tight. (insert crude innuendo here) Those bananas will work wonderfully in that amp.
I'd go with the better bi-wire cable over the double-up of the lower end cable.
__________________
Main: McIntosh XRT1K MDA1000 MC402 | JL F113 | Bryston BUC-1 | WireWorld Cabling | RGPC1200C | PPP
Office: Bel Canto S300iu 24/96 | KEF LS50 | REL R218 | WW Mini Eclipse | 18 TB Media Server Mobile: McIntosh MX406 MDA5000 MCD4000 MCC420M | JM Lab/Focal Utopia |
#5
|
||||
|
||||
Thanks Vesuvius,
I was just wondering if it would be better to use the single eclipse Bi- wire and Bi-amp with it. Or use the two runs of the diffent design . I think that they are both OCC copper but the geometry of the design is different .
__________________
Marantz( UD8004,AV8802a ), Oppo udp 203 JLAudio Fathom F-110, B&W( 802 series III , FCMS8, SCMS8) . WireWorld Eclipse 6 xlr(7) Sliver Eclipse 5.2 HDMI (3) electra 5.2 powercords . HRS Nimbus , lg 55 Oled Nvidia Shield PS Audio PPP System 2 Panasonic G25 Marantz av8003 |
#6
|
||||
|
||||
See second sentence above.
__________________
Main: McIntosh XRT1K MDA1000 MC402 | JL F113 | Bryston BUC-1 | WireWorld Cabling | RGPC1200C | PPP
Office: Bel Canto S300iu 24/96 | KEF LS50 | REL R218 | WW Mini Eclipse | 18 TB Media Server Mobile: McIntosh MX406 MDA5000 MCD4000 MCC420M | JM Lab/Focal Utopia |
#7
|
||||
|
||||
I does pay to read the whole answer doesn't it
__________________
Marantz( UD8004,AV8802a ), Oppo udp 203 JLAudio Fathom F-110, B&W( 802 series III , FCMS8, SCMS8) . WireWorld Eclipse 6 xlr(7) Sliver Eclipse 5.2 HDMI (3) electra 5.2 powercords . HRS Nimbus , lg 55 Oled Nvidia Shield PS Audio PPP System 2 Panasonic G25 Marantz av8003 |
#8
|
|||
|
|||
Bi-wire it. The banana's will work just fine on the Marantz.
Jim |
#9
|
||||
|
||||
Might this also depend upon the cable itself? With Kimber 8TC versus 12TC, using two pair of 8TC cables gets more conductors to my binding posts than one bi-wire 12TC would. My speakers are bi-wireable, and with 8TC I have 8 conductors on each terminal. With a single bi-wire pair of 12TC I'd have 8 conductors for low-frequency and 4 for high-frequency, according to Kimber. Since Wireworld cables are undoubtedly made differently this may not be an issue, but I thought I'd mention it anyway.
|
#10
|
||||
|
||||
Doug.......I see no purpose in bi-wiring other than increasing the cumulative wire gauge between the amp and speakers, which can be accomplished using single runs far more easily, and simplifies terminations.
Bi-amping is a whole different story, which requires independent speaker wire runs for each amplifier, and offers true audible improvements.
__________________
Dan STUDIO - McIntosh C1000C/P, MC2301 (2), MR88, Aurender N10, Esoteric K-01X, Shunyata Sigma spdif digital cable, Sonos Connect, PurePower 2000, Stillpoints, Furutech Flux 50, Michell Gyro SE, Michell HR Power Supply, SME 309, Ortofon Cadenza Black, Wireworld, Sonus faber Amati Anniversario LIVING ROOM - McIntosh C2300, MC75 (2), MR85, Magnum Dynalab 205, Simaudio MOON Neo 260D-T, Schiit Audio Yggdrasil, Aurender N100H, Shunyata Sigma USB cable, Micro Seiki DD40, Ortofon Cadenza Blue, Nakamichi BX-300, Sony 60ES DAT, PS Audio P10, Furutech Flux 50, Sonos Connect, Stillpoints, Wireworld, Kimber, PMC EB1i, JL Audio f113 VINTAGE - McIntosh MA230, Tandberg 3011A tuner, Olive 04HD, Sony DTC-59ES DAT, McIntosh 4300V, JBL 4312A |
|
|
Audio Aficionado Sponsors | |