AudioAficionado.org  

Go Back   AudioAficionado.org > The Lounge > Ye' Old Workshop

Ye' Old Workshop Build it or Break it, Never Fear!

Reply
 
Thread Tools Display Modes
  #1  
Old 05-29-2017, 08:38 AM
vintage_tube's Avatar
vintage_tube vintage_tube is online now
Just Pure Lucky



 
Join Date: Apr 2009
Location: East Coast
Posts: 8,749
Default Gutter Cleaner using Blower

I no longer get on a 12 foot or higher ladder and have a gutter on the back of the house on the 2d floor & the downspout always fills with debris in the fall. Additionally there is a gutter on the garage side of the house that I can get to with a step ladder.

Anyways, I'm tired of spending $85 to have someone schedule & come out to clean out the 2d floor gutter & elbow. Thought there has to be a something that I can make that would do the job well without a lot of jerry rigging.

So, I came up with this.

Used 4 pieces, 5 foot in length of 1.5 inch ABS DWV pipe which is lightweight & coupled 2 sections with ABS cement; making one 10 foot section (couldn't find longer 10 foot sections of ABS DWV pipe). Did the same with the remaining two 5 foot sections.

Added a flange to the end of one pipe which would be the used to connect to the shop vac hose & other end to the Stihl blower. To secure the hose at both ends I used duct tape. The 2d pipe would have a 45 degree elbow and a couple 22.5 degree elbows on one end that would be pointed down into the gutter -- blow the leaves out, etc.

Pictures shows the apparatus used to tackle the garage side gutter which is up about 10-12 feet & second shows tackling the 2d floor gutter.

Another picture shows the two 10 foot sections connected and reaching the 2d level. I used one inch white PVC (measure 1.25 inches wide) which I slid into the 1.5 inch ABS DWV and secured with four 2 inch screws (2 into one section & 2 into the other -- approx. 3 feet of white PVC is used). The use of the white PVC inside stabilizes & sturdies the temporary coupling of the two 10 foot ABS DWV sections, to reach the 2d level. To store in garage, remove the 4 screws/bolts connecting the two 10 foot sections together & slide the white PVC out of the ABS DWV pipe.

Cost: approx. $60

Bob
Attached Images
File Type: jpg flange to vac hose.JPG (147.0 KB, 132 views)
File Type: jpg cement & cleaner.JPG (87.6 KB, 127 views)
File Type: jpg hose to stihl.JPG (77.2 KB, 138 views)
File Type: jpg 2d floor gutter.JPG (64.8 KB, 143 views)
File Type: jpg 2 ten foot sections.JPG (74.5 KB, 152 views)
File Type: jpg Garage gutter.JPG (52.6 KB, 129 views)
File Type: jpg 2d floor ground.JPG (97.4 KB, 43 views)
__________________
Amps:VAC 450iQ Monos in Silver Flake on HRS M3X2-1921's, HRS G7 Footers/G-Links & Sound Anchor Conecoasters.
Preamp:VAC Master Preamplifier (Silver Flake)
Digital Source: dCS Rossini CD/SACD Transport, Vivaldi APEX DAC, Upsampler Plus & matching Clock (Silver)
Analogue Preamp:VAC Renaissance SE Phono stage in Silver Flake with XLR Output Option & with Nordost Valhalla XLR's.
Analogue Sources:SME 20/2 w/SME V arm & Nordost Valhalla TA cable, Palo Santos Presentation Cartridge & Akai GX-400D Reel-to-Reel w/relapped heads by JRF Magnetic Sciences. Akai RC-17 cabled remote (original owner since 1974).
Vibration Control:TT on HRS M3X2-1921 shelf.
Speakers:Wilson Audio Alexia in Argento Silver/Black grills sitting on Acoustic Diode Kit.
Power Cables:4 Nordost Odin Supreme Reference on amps, preamp & DAC. Ansuz Acoustics C2 on Transport & Clock.
Power Distribution Bar:Shunyata Everest 8000 w/Omega XC Power Cable.
Power Outlets:Furutech GTX-D NCF (R) duplex outlet, GTX Wall Plate & Duplex Cover (x2) on dedicated, same panel phase, 20A breakers.
Speaker Cables:3M Nordost Odin Supreme Reference on Nordost Sort Lifts.
Signal Cables:Nordost Odin XLR's on dCS DAC & Amps.
Digital Cables: Nordost Odin 2's, 110 ohm AES/EBU on dCS Transport to DAC.
Clock Cables:5 each 75 ohm 1.25M Nordost Valhalla BNC/BNC Digital
Ethernet Cable: WireWorld Platinum 1M Starlight® 8 Twinax
Headphones:Vintage Koss Pro IV AA.
RCM: Audio Desk PRO
Tube Test Gear:Mint late '60's/calibrated Heathkit TT-1A, MaxiMatcher Preamp & Space Tech Labs ATT-3.02 tube test sets.

Last edited by vintage_tube; 07-05-2017 at 06:51 AM.
Reply With Quote
  #2  
Old 05-29-2017, 10:37 AM
chessman's Avatar
chessman chessman is offline
From the BAT cave ...
 
Join Date: Jan 2010
Location: Columbus, OH
Posts: 11,697
Default

Ingenious!
Reply With Quote
  #3  
Old 05-29-2017, 01:16 PM
vintage_tube's Avatar
vintage_tube vintage_tube is online now
Just Pure Lucky



 
Join Date: Apr 2009
Location: East Coast
Posts: 8,749
Default

Quote:
Originally Posted by chessman View Post
Ingenious!
Thanks Randy.

Bob
__________________
Amps:VAC 450iQ Monos in Silver Flake on HRS M3X2-1921's, HRS G7 Footers/G-Links & Sound Anchor Conecoasters.
Preamp:VAC Master Preamplifier (Silver Flake)
Digital Source: dCS Rossini CD/SACD Transport, Vivaldi APEX DAC, Upsampler Plus & matching Clock (Silver)
Analogue Preamp:VAC Renaissance SE Phono stage in Silver Flake with XLR Output Option & with Nordost Valhalla XLR's.
Analogue Sources:SME 20/2 w/SME V arm & Nordost Valhalla TA cable, Palo Santos Presentation Cartridge & Akai GX-400D Reel-to-Reel w/relapped heads by JRF Magnetic Sciences. Akai RC-17 cabled remote (original owner since 1974).
Vibration Control:TT on HRS M3X2-1921 shelf.
Speakers:Wilson Audio Alexia in Argento Silver/Black grills sitting on Acoustic Diode Kit.
Power Cables:4 Nordost Odin Supreme Reference on amps, preamp & DAC. Ansuz Acoustics C2 on Transport & Clock.
Power Distribution Bar:Shunyata Everest 8000 w/Omega XC Power Cable.
Power Outlets:Furutech GTX-D NCF (R) duplex outlet, GTX Wall Plate & Duplex Cover (x2) on dedicated, same panel phase, 20A breakers.
Speaker Cables:3M Nordost Odin Supreme Reference on Nordost Sort Lifts.
Signal Cables:Nordost Odin XLR's on dCS DAC & Amps.
Digital Cables: Nordost Odin 2's, 110 ohm AES/EBU on dCS Transport to DAC.
Clock Cables:5 each 75 ohm 1.25M Nordost Valhalla BNC/BNC Digital
Ethernet Cable: WireWorld Platinum 1M Starlight® 8 Twinax
Headphones:Vintage Koss Pro IV AA.
RCM: Audio Desk PRO
Tube Test Gear:Mint late '60's/calibrated Heathkit TT-1A, MaxiMatcher Preamp & Space Tech Labs ATT-3.02 tube test sets.
Reply With Quote
  #4  
Old 05-30-2017, 09:11 AM
John James's Avatar
John James John James is offline
Senior Member
 
Join Date: May 2009
Location: Piney Flats, Tn.
Posts: 537
Default

Hard-hat and safety glasses?
__________________
John
Reply With Quote
  #5  
Old 06-12-2017, 08:10 AM
vintage_tube's Avatar
vintage_tube vintage_tube is online now
Just Pure Lucky



 
Join Date: Apr 2009
Location: East Coast
Posts: 8,749
Default

Was catching up with a neighbor and his plans for the summer, etc., and somehow the conversation shifted to the heavy rains we had last week & subsequently his 2d floor gutters were giving him some grief as they were clogged with leaves and pine needles, especially where two roof valleys fed to the gutter. Well, needless to say, he was speaking my language and mentioned I had a possible immediate solution & headed to the house/garage to fetch my contraption.

Picked up the Stihl blower, the shop VAC hose, duct tape, wrench, and the two ABS DWV pipe sections. In his backyard, assembled the two pipe sections, securing the two together with the 2 inch screws/nuts.

Slid the 20 foot long 1/2 inch pipe up & along the corner of the house, using the downspout as a 'brace' and hung it off the 2d floor gutter. Attached the VAC hose to the pipe using duct tape & the other end to the Stihl blower, securing a tight fit of the blower nozzle also with duct tape.

Fired up the Stihl blower, locking it on high. Maneuvered the pipe along the gutter and leaves were blowing out of the gutter and trickling to the ground (forgot to bring my eye protection). Walked the pipe nozzle left and right of the gutter -- leaves being disturbed & cleared from the gutter.

Located the valley area where you could see pine needles clogging the gutter and moved the pipe left & right -- but nothing happening. No debris flying like with the leaves. After awhile we realized the pine needles, which have been there for sometime, are caked into the valley & gutter. The blower doesn't have the velocity to break it up; so, the old fashioned ladder & gloved hand method is required. Which we'll tacked Wednesday when I have access to a 32 foot ladder.

Again though, the contraption worked great on leaves and clearing out all the other areas. I'll still give it 5 of these

Bob
__________________
Amps:VAC 450iQ Monos in Silver Flake on HRS M3X2-1921's, HRS G7 Footers/G-Links & Sound Anchor Conecoasters.
Preamp:VAC Master Preamplifier (Silver Flake)
Digital Source: dCS Rossini CD/SACD Transport, Vivaldi APEX DAC, Upsampler Plus & matching Clock (Silver)
Analogue Preamp:VAC Renaissance SE Phono stage in Silver Flake with XLR Output Option & with Nordost Valhalla XLR's.
Analogue Sources:SME 20/2 w/SME V arm & Nordost Valhalla TA cable, Palo Santos Presentation Cartridge & Akai GX-400D Reel-to-Reel w/relapped heads by JRF Magnetic Sciences. Akai RC-17 cabled remote (original owner since 1974).
Vibration Control:TT on HRS M3X2-1921 shelf.
Speakers:Wilson Audio Alexia in Argento Silver/Black grills sitting on Acoustic Diode Kit.
Power Cables:4 Nordost Odin Supreme Reference on amps, preamp & DAC. Ansuz Acoustics C2 on Transport & Clock.
Power Distribution Bar:Shunyata Everest 8000 w/Omega XC Power Cable.
Power Outlets:Furutech GTX-D NCF (R) duplex outlet, GTX Wall Plate & Duplex Cover (x2) on dedicated, same panel phase, 20A breakers.
Speaker Cables:3M Nordost Odin Supreme Reference on Nordost Sort Lifts.
Signal Cables:Nordost Odin XLR's on dCS DAC & Amps.
Digital Cables: Nordost Odin 2's, 110 ohm AES/EBU on dCS Transport to DAC.
Clock Cables:5 each 75 ohm 1.25M Nordost Valhalla BNC/BNC Digital
Ethernet Cable: WireWorld Platinum 1M Starlight® 8 Twinax
Headphones:Vintage Koss Pro IV AA.
RCM: Audio Desk PRO
Tube Test Gear:Mint late '60's/calibrated Heathkit TT-1A, MaxiMatcher Preamp & Space Tech Labs ATT-3.02 tube test sets.
Reply With Quote
  #6  
Old 06-12-2017, 12:43 PM
jdandy's Avatar
jdandy jdandy is offline
Merry Christmas to all



 
Join Date: Apr 2009
Location: North Central Florida
Posts: 53,224
Default

Bob.......You neighbor is fortunate that you are ingenious and willing to offer your time and equipment to help him with his chore.
__________________
Dan



STUDIO - McIntosh C1000C/P, MC2301 (2), MR88, Aurender N10, Esoteric K-01X, Shunyata Sigma spdif digital cable, Sonos Connect, PurePower 2000, Stillpoints, Furutech Flux 50, Michell Gyro SE, Michell HR Power Supply, SME 309, Ortofon Cadenza Black, Wireworld, Sonus faber Amati Anniversario
LIVING ROOM - McIntosh C2300, MC75 (2), MR85, Magnum Dynalab 205, Simaudio MOON Neo 260D-T, Schiit Audio Yggdrasil, Aurender N100H, Shunyata Sigma USB cable, Micro Seiki DD40, Ortofon Cadenza Blue, Nakamichi BX-300, Sony 60ES DAT, PS Audio P10, Furutech Flux 50, Sonos Connect, Stillpoints, Wireworld, Kimber, PMC EB1i, JL Audio f113
VINTAGE - McIntosh MA230, Tandberg 3011A tuner, Olive 04HD, Sony DTC-59ES DAT, McIntosh 4300V, JBL 4312A
Reply With Quote
  #7  
Old 12-04-2017, 05:02 PM
vintage_tube's Avatar
vintage_tube vintage_tube is online now
Just Pure Lucky



 
Join Date: Apr 2009
Location: East Coast
Posts: 8,749
Default

Most of the leaves have fallen & that time of year again with no need to schedule a service crew to clean my 1st and 2d floor gutters --- and pay a service visit & subsequent labor fees.

Just cleaned all gutters in about 45 minutes -- clean as a whistle as they say.

Maybe one more thorough cleaning in a week -10 days and in the meantime visit MD/AS or ED for some music instead.

Just a bump for those who do their own yardwork/maintenance & with leaf/gutter issues.

Best Sirs,

Bob
__________________
Amps:VAC 450iQ Monos in Silver Flake on HRS M3X2-1921's, HRS G7 Footers/G-Links & Sound Anchor Conecoasters.
Preamp:VAC Master Preamplifier (Silver Flake)
Digital Source: dCS Rossini CD/SACD Transport, Vivaldi APEX DAC, Upsampler Plus & matching Clock (Silver)
Analogue Preamp:VAC Renaissance SE Phono stage in Silver Flake with XLR Output Option & with Nordost Valhalla XLR's.
Analogue Sources:SME 20/2 w/SME V arm & Nordost Valhalla TA cable, Palo Santos Presentation Cartridge & Akai GX-400D Reel-to-Reel w/relapped heads by JRF Magnetic Sciences. Akai RC-17 cabled remote (original owner since 1974).
Vibration Control:TT on HRS M3X2-1921 shelf.
Speakers:Wilson Audio Alexia in Argento Silver/Black grills sitting on Acoustic Diode Kit.
Power Cables:4 Nordost Odin Supreme Reference on amps, preamp & DAC. Ansuz Acoustics C2 on Transport & Clock.
Power Distribution Bar:Shunyata Everest 8000 w/Omega XC Power Cable.
Power Outlets:Furutech GTX-D NCF (R) duplex outlet, GTX Wall Plate & Duplex Cover (x2) on dedicated, same panel phase, 20A breakers.
Speaker Cables:3M Nordost Odin Supreme Reference on Nordost Sort Lifts.
Signal Cables:Nordost Odin XLR's on dCS DAC & Amps.
Digital Cables: Nordost Odin 2's, 110 ohm AES/EBU on dCS Transport to DAC.
Clock Cables:5 each 75 ohm 1.25M Nordost Valhalla BNC/BNC Digital
Ethernet Cable: WireWorld Platinum 1M Starlight® 8 Twinax
Headphones:Vintage Koss Pro IV AA.
RCM: Audio Desk PRO
Tube Test Gear:Mint late '60's/calibrated Heathkit TT-1A, MaxiMatcher Preamp & Space Tech Labs ATT-3.02 tube test sets.
Reply With Quote
  #8  
Old 12-04-2017, 11:14 PM
Karl Maga Karl Maga is offline
Member
 
Join Date: May 2017
Posts: 358
Default

Bob, as I have no pine needles to contend with, only oak and hickory leaves, my solution may not be helpful for you. But, I had a forgotten brand of gutter screen installed on all gutters and what used to be a chore similar to yours is no longer required. I paid less than $500.

This was the first season they were in place, man was it satisfying! I literally did nothing but blow/rake/vacuum them on the ground. But I like your contraption, nicely done!

Last edited by Karl Maga; 12-04-2017 at 11:17 PM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Audioaficionado.org tested by Norton Internet Security

All times are GMT -4. The time now is 07:23 PM.



Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
©Copyright 2009-2023 AudioAficionado.org.Privately owned, All Rights Reserved.
Audio Aficionado Sponsors
AudioAficionado Subscriber
AudioAficionado Subscriber
Inspire By Dennis Had
Inspire By Dennis Had
Harmonic Resolution Systems
Harmonic Resolution Systems
Wyred4Sound
Wyred4Sound
Dragonfire Acoustics
Dragonfire Acoustics
GIK Acoustics
GIK Acoustics
Esoteric
Esoteric
AC Infinity
AC Infinity
JL Audio
JL Audio
Add Powr
Add Powr
Accuphase - Soulution
Accuphase - Soulution
Audio by E
Audio by E
Canton
Canton
Bryston
Bryston
WireWorld Cables
WireWorld Cables
Stillpoints
Stillpoints
Bricasti Design
Bricasti Design
Furutech
Furutech
Shunyata Research
Shunyata Research
Legend Audio & Video
Legend Audio & Video