#11
|
|||
|
|||
Oh, yes. Mine is in rosewood and stunning, having been refinished. Now I just have to see how best to connect the rather funny looking two prong breaker. I have never seen connectors like on that thing.
|
#12
|
||||
|
||||
Steve,
Post a pic of the breaker and measure the dimensions of the terminals - I can probably find the correct connectors. Tom
__________________
Main System: Amati Futura Mains Amati Homage VOX Center, Proac Response 1sc Rears, Three MC2301's for L,C,R MC 602 for the rears C 1100, MX 151, MCD 1100, MR 80 Nottingham Dais with Wave Mechanic Sumiko Palo Santos Presentation SurfacePro 3, RPi 4, ROON, WW Starlight Platinum USB, Schiit Yggdrasil, Benchmark DAC3 HGC MX 151, OppO BDP-95, JVC RS-500 DILA projector, 106" diagonal Stewart Luxus Screenwall Deluxe with Studiotek 130 G3 material. Lake House: Ohm F, MC 275V, C2300, MR 77, Rega P3 OnDeck: McIntosh MAC 4300v |
#13
|
|||
|
|||
Much obliged! Will do once I get it. Should not be long.
|
#14
|
|||
|
|||
Looks like the contact prongs are 1/4" in length, about 5/16-3/8" stagger (offset) Body of the thing not counting the contacts in only about 3/4".
|
#15
|
||||
|
||||
Steve,
Could you measure the diameter of the terminals themselves? I looked at the pic online and as far as I can tell those are solder terminals. But depending on the diameter of the terminal I may be able to find a crimp terminal that will work. Tom
__________________
Main System: Amati Futura Mains Amati Homage VOX Center, Proac Response 1sc Rears, Three MC2301's for L,C,R MC 602 for the rears C 1100, MX 151, MCD 1100, MR 80 Nottingham Dais with Wave Mechanic Sumiko Palo Santos Presentation SurfacePro 3, RPi 4, ROON, WW Starlight Platinum USB, Schiit Yggdrasil, Benchmark DAC3 HGC MX 151, OppO BDP-95, JVC RS-500 DILA projector, 106" diagonal Stewart Luxus Screenwall Deluxe with Studiotek 130 G3 material. Lake House: Ohm F, MC 275V, C2300, MR 77, Rega P3 OnDeck: McIntosh MAC 4300v |
#16
|
|||
|
|||
Thanks, Tom. Yes, these are circuit board chassis pins apparently. Turns out I was able to figure something out with the help of a car audio guy and a computer guy. Bought a single auto fuse holder (with cable in and out) and a fuse for same (you know the flat type with the wavy element in it). The computer guy will solder the pins of the breaker to the fuse, then plug it in and test for continuity of course. Should be fine. Next will be to see if it cuts out too often, though I doubt it will as it is not often it gets those high sound levels. Can always go up a step if needed.
Much appreciated your time on this in any event, Tom. Thanks! |
#17
|
||||
|
||||
Glad you've found a solution!
__________________
Main System: Amati Futura Mains Amati Homage VOX Center, Proac Response 1sc Rears, Three MC2301's for L,C,R MC 602 for the rears C 1100, MX 151, MCD 1100, MR 80 Nottingham Dais with Wave Mechanic Sumiko Palo Santos Presentation SurfacePro 3, RPi 4, ROON, WW Starlight Platinum USB, Schiit Yggdrasil, Benchmark DAC3 HGC MX 151, OppO BDP-95, JVC RS-500 DILA projector, 106" diagonal Stewart Luxus Screenwall Deluxe with Studiotek 130 G3 material. Lake House: Ohm F, MC 275V, C2300, MR 77, Rega P3 OnDeck: McIntosh MAC 4300v |
#18
|
|||
|
|||
|
#19
|
|||
|
|||
Have had this breaker in place for quite a while now and it seems to be working out great, By now I know I would have replaced a fuse or two.......... If you have an older sub that is popping its fuse, this should work for you also.
|
|
|
Audio Aficionado Sponsors | |