#81
|
|||
|
|||
|
#82
|
|||
|
|||
|
#83
|
|||
|
|||
Last edited by SCAudiophile; 12-28-2016 at 10:15 AM. |
#84
|
||||
|
||||
Breathtaking. Beautiful. Bravo!!
|
#85
|
|||
|
|||
Thank you!
|
#86
|
|||
|
|||
Sweeeeet!
|
#87
|
|||
|
|||
Thanks man...those are the sounds coming out after only 150+ hours, kind of scary thinking they are less than 1/3 on their way to broken in! Very musical, rock solid sound stage, imaging, instrument and voices, not forward or harsh, just right!
|
#88
|
|||
|
|||
One thing I forgot to mention along with latest photos; in some there are Ultra5s footers with spikes on the speakers and in the final config at present, they are not on the R1s and they are resting on carpet. The ULTRA5s will soon be back on the R1s (no spikes) once I get new coupling bolts (expected tomorrow) thanks to Ivan. Given the nature of the carpet and sub-floor here and the load-bearing ability of the short threaded section of the bolt (about 1/2" long and small diameter) that goes into the ULTRA5 compared to the large section (larger diameter, about 2" long) that goes into the speaker, when the speakers were leaned to attach the feet and then lowered back into position to be leaned to the other side to attach the 3rd footer, the spikes being massive as they are "bit hard" into the floor and did not move. The resulting stress on the small end of the coupling bolt was a bit too much and I noticed that the footers were bent on the first side of the speaker that underwent the most stress. Part of this is due to the amount of recess tapped into the bottom on the R1 and the ULTRA5 being apart from the base by about 1/2". Very desirable sonically but for a 330 lb speaker bearing down on the small end with the speaker at an angle, then restored, and tilted again to the other side, the force vectors were apparently a bit too much.
Lesson Learned: I would not recommend use of spikes on these speakers even with carpet. In retrospect, the R1s have enough sheer mass and the 3 point pattern given the surface area of the ULTRA5 footers bases is more than sufficient to couple them to any surface including carpet. If this is not clear, let me know and I'll try to clarify it better. |
#89
|
|||
|
|||
Good morning all! Had my other set of multi-ribbon jumpers re-terminated with Furutech CF-202 (R) Banana plugs. The Bocchino banana plugs are first rate sonically and build quality giving me great results over the last couple of years and the Bocchino spades' quality and heft is obvious from the photos but the TAD R1 binding posts are huge as stated previously and I had to use a screwdriver to open up the veins on the bananas manually to get them to remain in the large holes in the binding posts. Obviously not a great long-term solution as they will loosen a bit over time. I had these 2 pair of jumpers re-terminated as they have a further 2 additional layers of ribbons over my first pair.
The Furutech CF-202 (R) Bananas are serious stuff, they feature a carbon fiber & non-magnetic stainless barrel assembly that when turned counter-clockwise, causes the mechanism to variably deploy and lock the banana in the binding post with fins that can be expanded to just the right size to fit whatever binding post you have and feature other notable things in their build as well including a damping ring. In short they lock in, stay there and sound great. Burn-in on the speakers at a slower pace due to work/life realities continues. It's amazing to me just how good these speakers are and that's after only 225 hours or so. Stunning! Photos; Last edited by SCAudiophile; 01-06-2017 at 07:44 AM. |
#90
|
|||
|
|||
Wow! Great system and looks beautiful too. I heard some Legacy speakers a couple of years ago at a show and they were very impressive. Enjoy.
|
|
|
Audio Aficionado Sponsors | |