#11
|
|||
|
|||
Thanks for the update. I'm sure we can get it figured out. There's only so many places a problem like that will occur, usually in the form of a phase of the balanced circuitry not being connected somewhere. I think we should be able to track it down in short order even if it is a heat-related problem.
__________________
Industry Affiliation - Ayre CEO |
#12
|
||||
|
||||
Hi RLF. Should a kept your Ref 6?
|
#13
|
|||
|
|||
Ryan. Thank you for the follow up. Needless to say, I was shocked when my dealer called and told me that they could not reproduce the problem in the store. We’ll see if it starts occurring after they finish running it over night. I would like to think that it is heat related too, but when my dealer asked me to unplug it overnight and then turned it on the next morning, it still exhibited the same balance problem even when cold. I highly doubt that it is a problem elsewhere in my system since my loaner ARC preamp is all balanced too and the balance is spot on with both channels playing at the same level.
My dealer will be in touch with me today. I’ll ask him to send my KX-R to you to check out thoroughly at Ayre if you believe that you can get to the bottom of this. Much appreciated. Bob |
#14
|
||||
|
||||
Quote:
Bob - have you tried a different set of interconnects from the preamp to your power amp? Tom
__________________
Main System: Amati Futura Mains Amati Homage VOX Center, Proac Response 1sc Rears, Three MC2301's for L,C,R MC 602 for the rears C 1100, MX 151, MCD 1100, MR 80 Nottingham Dais with Wave Mechanic Sumiko Palo Santos Presentation SurfacePro 3, RPi 4, ROON, WW Starlight Platinum USB, Schiit Yggdrasil, Benchmark DAC3 HGC MX 151, OppO BDP-95, JVC RS-500 DILA projector, 106" diagonal Stewart Luxus Screenwall Deluxe with Studiotek 130 G3 material. Lake House: Ohm F, MC 275V, C2300, MR 77, Rega P3 OnDeck: McIntosh MAC 4300v |
#15
|
|||
|
|||
Tom. Thanks for the suggestion. I didnt try a different set of interconnects, but since everything is ok with my loaner preamp into my MX-R amps using the same interconnects, I doubt that’s the source of the problem. At the time that I first reported the problem to my dealer, he didn’t think so either, but I will ask him again. It’s interesting that Ayre products balanced inputs and outputs don’t have the clip to lock them in place. I did make sure that they were inserted into the connection all the way and snug at both ends though.
|
#16
|
|||
|
|||
Follow up
My dealer just called me and said that the preamp has started to drift at about 1.5dB off center which he said it wasn’t doing earlier in the morning, so apparently a long warm up time is the key. As time went on, my drift got significantly worse. At this point, neither he or I believe that it was doing it when he first put in my system and that it took several days to become significant. At least it is now acting up at the dealer and will go back to Ayre for a fix.
|
#17
|
|||
|
|||
Quote:
|
#18
|
|||
|
|||
Yes indeed, I have been a long time customer of theirs and they have always provided top notch service and support.
|
#19
|
||||
|
||||
Good to see that your dealer can duplicate the issue. Godspeed in getting it fixed and back in your system.
Tom
__________________
Main System: Amati Futura Mains Amati Homage VOX Center, Proac Response 1sc Rears, Three MC2301's for L,C,R MC 602 for the rears C 1100, MX 151, MCD 1100, MR 80 Nottingham Dais with Wave Mechanic Sumiko Palo Santos Presentation SurfacePro 3, RPi 4, ROON, WW Starlight Platinum USB, Schiit Yggdrasil, Benchmark DAC3 HGC MX 151, OppO BDP-95, JVC RS-500 DILA projector, 106" diagonal Stewart Luxus Screenwall Deluxe with Studiotek 130 G3 material. Lake House: Ohm F, MC 275V, C2300, MR 77, Rega P3 OnDeck: McIntosh MAC 4300v |
#20
|
|||
|
|||
Quote:
Bob |
|
|
Audio Aficionado Sponsors | |