#1
|
|||
|
|||
P10 heat
Hello,
Seeking feedback on how much heat the newer p10 power regeneration units produce. Do not want to cook equipment above it in a rack if it gets hot. Thanks in advance.
__________________
|
#2
|
||||
|
||||
Mine has been powering my entire system, 2 tube amplifier and all my front end equipment. It gets warm enough where the heat sinks on the side are close to being uncomfortable to the touch. I wouldn’t put mine in a rack without a fan and lots of breathing room in front and back.
__________________
Main Equipment: Kharma Elegance dB11-S, JL Audio F113v2 X 2, Block Audio Line & Mono SE Amplification, Bricasti M21 DAC, Antipodes Kala K-50 Server, Clearaudio Performance SE. Satisfy tonearm & Maestro Wood MM cartridge. Power: Shunyata Everest 8000, Sigma XC v2, Sigma NR v2, Block Audio PCs, Defender, ADDPowr Wizard Grounding: Shunyata Altaira CGS - 4 X Alpha CGS cables, Network : Supra Cat 8+, Twin (Nenon) Modified Buffalo GS2016 Switches, Keces P3 LPSU, Cables: Wireworld Platinum 8 USB, Wireworld Platinum Eclipse 8 Speaker cables, 6M & 1M Tubulus Concentus ICs, Other:Two PSI Audio AVAA C20, Multiple GIK products, Stillpoint Apertures, Stillpoint Minis and Ultra SS, Three 20 Amp lines, Furutech GTX - Gold outlets, Adona Rack |
#3
|
|||
|
|||
I appreciate the feedback- thanks.
__________________
|
#4
|
||||
|
||||
Quote:
Hello - What is the average load the P10 is addressing in your system? |
#5
|
||||
|
||||
Quote:
I’m not sure what it was. I recently gave both amps their own 20 AMP line and have started listening that way. Not sure I can tell the difference as other changes happened at the same time. Next week, I will reconnect the Amps to the P10 and listen.
__________________
Main Equipment: Kharma Elegance dB11-S, JL Audio F113v2 X 2, Block Audio Line & Mono SE Amplification, Bricasti M21 DAC, Antipodes Kala K-50 Server, Clearaudio Performance SE. Satisfy tonearm & Maestro Wood MM cartridge. Power: Shunyata Everest 8000, Sigma XC v2, Sigma NR v2, Block Audio PCs, Defender, ADDPowr Wizard Grounding: Shunyata Altaira CGS - 4 X Alpha CGS cables, Network : Supra Cat 8+, Twin (Nenon) Modified Buffalo GS2016 Switches, Keces P3 LPSU, Cables: Wireworld Platinum 8 USB, Wireworld Platinum Eclipse 8 Speaker cables, 6M & 1M Tubulus Concentus ICs, Other:Two PSI Audio AVAA C20, Multiple GIK products, Stillpoint Apertures, Stillpoint Minis and Ultra SS, Three 20 Amp lines, Furutech GTX - Gold outlets, Adona Rack |
#6
|
||||
|
||||
P10 heat
Duplicate
__________________
Main Equipment: Kharma Elegance dB11-S, JL Audio F113v2 X 2, Block Audio Line & Mono SE Amplification, Bricasti M21 DAC, Antipodes Kala K-50 Server, Clearaudio Performance SE. Satisfy tonearm & Maestro Wood MM cartridge. Power: Shunyata Everest 8000, Sigma XC v2, Sigma NR v2, Block Audio PCs, Defender, ADDPowr Wizard Grounding: Shunyata Altaira CGS - 4 X Alpha CGS cables, Network : Supra Cat 8+, Twin (Nenon) Modified Buffalo GS2016 Switches, Keces P3 LPSU, Cables: Wireworld Platinum 8 USB, Wireworld Platinum Eclipse 8 Speaker cables, 6M & 1M Tubulus Concentus ICs, Other:Two PSI Audio AVAA C20, Multiple GIK products, Stillpoint Apertures, Stillpoint Minis and Ultra SS, Three 20 Amp lines, Furutech GTX - Gold outlets, Adona Rack Last edited by crwilli; 01-10-2018 at 11:53 PM. |
#7
|
||||
|
||||
My P10 sits on its own on top of a cabinet containing LPs, between the wall outlet and my rack. That way it has free space and air around it and never gets very hot.
__________________
Avid Acutus SP, NO ARM, Benz Micro LP-S, Whest Audio PS.40RDT SE, PS Audio DSMP+DS DAC, Simaudio Moon 700i, Dali Epicon 6, Simaudio Moon Nēo 430HAD, HiFiMan HE-1000v2, Chord Sarum SA XLR, RCA, USB, Chord Sarum speaker, Nordost Vishnu power, Furutech plugs, PS Audio P10+Chord Sarum SA power, Stillpoints Ultra SS, Ultra Mini and LPI, HiFi Racks rack, Audio Desk Systeme PRO+Keith Monks Omni RCM |
#8
|
|||
|
|||
My entire front end is connected to a P10 (preamp, sacd player, master clock generator, bluray player).
The display shows a 7% load, my P10 runs cold all the time. My Pass X600 monoblock's are plugged directly to the wall outlet. Best Pablo |
#9
|
||||
|
||||
I plug in all components for my own reasons and the load on average is 30% pulling 3-4 amps and gets faintly warm, your hand can stay on the fins indefinitely
|
#10
|
||||
|
||||
P10 heat
With just my front end - PreAmp, SilenZio, crossover, Master clock, SACD player - and Powered sub, the load is 15% and warm but not hot. That would probably be okay in a well ventilated rack.
With the Amps added, the load goes to 69% and that is when it gets hot, ALMOST uncomfortable to touch but you can still hold it. Have you reached out to PS Audio for their suggestions and input?
__________________
Main Equipment: Kharma Elegance dB11-S, JL Audio F113v2 X 2, Block Audio Line & Mono SE Amplification, Bricasti M21 DAC, Antipodes Kala K-50 Server, Clearaudio Performance SE. Satisfy tonearm & Maestro Wood MM cartridge. Power: Shunyata Everest 8000, Sigma XC v2, Sigma NR v2, Block Audio PCs, Defender, ADDPowr Wizard Grounding: Shunyata Altaira CGS - 4 X Alpha CGS cables, Network : Supra Cat 8+, Twin (Nenon) Modified Buffalo GS2016 Switches, Keces P3 LPSU, Cables: Wireworld Platinum 8 USB, Wireworld Platinum Eclipse 8 Speaker cables, 6M & 1M Tubulus Concentus ICs, Other:Two PSI Audio AVAA C20, Multiple GIK products, Stillpoint Apertures, Stillpoint Minis and Ultra SS, Three 20 Amp lines, Furutech GTX - Gold outlets, Adona Rack Last edited by crwilli; 01-11-2018 at 12:27 PM. |
|
|
Audio Aficionado Sponsors | |